find your year on link below.

the info may be more thorough.

Subaru Keyless Entry, Security Alarm, Immobilizer Key, Remote Start Systems. Most years and models

 

Thank you canubaru..... Just tried it !!! It worked !!!!

If you were closer I'd buy you a cold beer......or an Ice Cream !!!!

Again..............MUCH APPRECIATED

If ever in the area.................let me know.

I am about 1/2 hour North of Boston....

 

Pretty sure CARDOC likes Snapon gift certificates. LOL

 

I don't buy from Snap On unless they are the only one with the tool or set I need. They are overpriced and it takes too long to warranty a tool.

 

Thank you canubaru..... Just tried it !!! It worked !!!!

you are welcome.

but be aware, if you lock the car, and then open with a key, the alarm will sound.
there is no way to avoid this EXCEPT valet mode.
and as you know, valet mode = alarm off.

Pretty sure CARDOC likes Snapon gift certificates. LOL

wrong thread?

 

wrong thread?

I think at the rate that cardoc answers everyone's questions, people start to assume it is him when a question is answered.

 

Thanks to all of u! This is exactly what mine was doing the doors would lock and unlock, but the alarm wouldn't set. Now it works! Thank you!

 

Sorry for bumping this old thread.....Just went through this when I installed the Alpine alarm and keyless entry into my wagon. Opening the drivers door and holding the unlock button didn't work on the new teardrop remote. But opening the drivers door and pressing the "trunk release" button worked flawless. No need to hold for 2-3 seconds. Just open the door and tap the button. this is for a 2002 Legacy Alpine alarm with 3 button teardrop remote. I hope this helps someone in the future

Seems that older teardrops are 2 button and should work by holding the unlock button for 2-3 seconds as mentioned earlier in the thread and newer ones are 3 button and work by tapping the trunk release.

 

Stuck in Valet...
It tried the instructions from the link that Canubaru posted, but it didn't do anything. I have the teardrop remote. The original remote used to work for getting it in and out of Valet, but I can't get it out using the teardrop. lock and unlock works fine.

History: the car was recently stolen and recovered, and I'm not sure if something was messed up in the process. The original remote no longer does anything, but the light indicates that it's transmitting.

ideas?

 

red brake light, security activated, no start

I have a 2001 Subaru Outback, the red brake light is on and security light is on dash and car will not start, once in a while it will start and die, then sometimes it does nothing. all electronics work, any ideas?

 

ignition locks

ok, what am i doing that causes this ?
click my remote open door button but sometime when i get in and try to start the vehicle the key will not turn. I've tried starting with the remote start, put the key in the ignition and the engine stops as it should, then the key turns and i can start the engine again. i'm thinking this has to do with the security, just need to know how to stop this from happening.
Junbug0

 

ok, what am i doing that causes this ?
click my remote open door button but sometime when i get in and try to start the vehicle the key will not turn. I've tried starting with the remote start, put the key in the ignition and the engine stops as it should, then the key turns and i can start the engine again. i'm thinking this has to do with the security, just need to know how to stop this from happening.
Junbug0

seeing as how the cars made in these years did not come with remote start, I guess you got that as a aftermarket system....

so you would have to find the information on the manufacturer's website for that aftermarket alarm / autostart package.

here is the information for 2000-2004 OEM auto locks and optional security that was Alpine based. (which you may still have on the car, if the autostart system does only that).

Subaru Keyless Entry, Security Alarm, Immobilizer Key, Remote Start Systems. Most years and models